Are you tired of carrying about bulky chemical cleaners in order to maintain the cleanliness of your jetted tub? So why not give it a shot and add some Dishwasher Tablets?
Prepare to remove the filth and grime accumulation by following these tips on how to clean a jetted tub with dishwashing tablets. For a sparkling tub, follow each process from shutting off the power to filling the tub with hot water, adding dishwashing tablets, emptying the water, cleaning it out, and refilling it.
This cleaning procedure not only helps return your jetted tub to its former glory, exactly like new ones, but it also helps save you a ton of time and energy.
In only seven simple stages, our tutorial will demonstrate how dishwashing tablets may provide powerful cleaning for a thorough sanitization. Let’s begin, then.
How to Unclog a Jetted Bathtub Using Dishwasher Tabs?
Dishwasher tablets are a simple and efficient way to clean a jetted tub. With little work and equipment needed, this procedure produces excellent results. To make your jetted tub (also known as whirlpool tub) feel and look brand new, follow these instructions:
STEP 1: Disconnect the power
The electricity to your jetted tub needs to be turned off first. The circuit that operates your bathtub jets or whirlpool should be turned off at the breaker box. Before beginning any cleaning process, make sure it is fully off.
While working on any electrical equipment, make sure all electricity sources are turned off.
STEP 2: Add Hot Water to the Tub
Now, fill the remaining two-thirds of your bathtub with hot water. For optimal results, use hot tap water; however, don’t let it get too hot, since this might harm some bathtub materials.
Before beginning the cleaning process, make sure to find out whether your particular model has any temperature restrictions.
Step 3: Add a dishwasher tablet
After the tub is full of hot water, depending on how unclean it is and how much gunk has to be cleaned out of the pipes and jets of your jetted bathtub, add one or two dishwashing detergent tablets to the water.
Let these tablets to dissolve completely and release their potent cleaning ingredients into the solution without being disturbed by movement or turbulence in the hot water for around 15 minutes. This can happen when air pumps connected to some bathtubs or spas suck the water or stir the water.
Step 4: Run the Jets
Now activate the jets or whirlpool in your bathtub to generate enough turbulence to move and combine the hot water and dishwashing tablet in the solution.
Dissolving dishwashing tablets will provide you strong cleaning chemicals that can go into every nook and cranny of your jetted bathtub, making them more effective at getting rid of filth, grime, and other unpleasant items in pipes and other difficult-to-reach areas.
After using your tub, empty all the solutions and leave them running for another 15 minutes before turning them off once more.
Step 5; Drain the Water
Drain the water from your jetted tub after 15 minutes to clean and unclog the jets. Find the drain valve, which is often in the center, near the tub’s base. With the tub’s electricity completely off, remove the drain stopper with a flathead screwdriver.
Step 6: Rinse the tub and refill it
It’s time to rinse out all of the soapy buildup from your jetted tub’s inner surface now that you’ve drained the water from it completely. To help flush away any leftover soap residue, fill the tub with clean, warm water and turn on the jets for about two minutes.
Fill your jetted bathtub with clean water until it is just below the tub jets after properly rinsing it. To prevent water from escaping while you replenish, make sure that all valves and plugs are well closed.
STEP 7. Restart the power
When the dishwashing tablets have done their job and freed the blockages in your jetted bathtub, turn on the main power switches. You may have a rejuvenated, clog-free jetted bathtub experience by turning on all relevant power switches once again.
What should you do before using dishwasher tablets to clean your jetted tub?
Dishwasher tablets are a fantastic way to keep your jetted tub looking and feeling its best. To make sure the procedure runs successfully, there are a few things you need do before you begin:
- Carefully read all of the labels on the product packaging, and adhere to the directions exactly. You may prevent potential harm to your jetted tub by doing this.
- Make sure there is at least two inches of hot or warm water covering the jets. Add one or two dishwashing detergent tablets to the water as you fill the tub. Any dirt and filth that could be lodged in the jets will be broken down by this.
- Make sure you have all the tools you’ll need for cleaning, including rubber gloves, dishwashing tablets, an old toothbrush or scrub brush, a clean cloth, or sponge.
- Towels, clothing, toys, and other anything that could be in touch with standing water should all be removed from the area around the hot tub. By doing this, you can prevent slipping on damp surfaces and accidently breaking things.
- Examine the tub’s jets, pipes, and other fittings for any obvious indications of wear or damage so that any issues may be fixed before more harm is done.
- Check your hot tub’s drain plug to make sure it is securely fastened so that water cannot leak out when you are using dishwashing tablets to clean it.
- Around 2-3 inches of warm water should be added to your whirlpool tub before adding the dishwashing tablets to prevent splashing or overflow. You should be aware that using too much water might make cleaning less effective.
- Most importantly, for your own safety, always use dishwashing tablets while wearing rubber gloves. since prolonged exposure to these compounds without protection might result in skin discomfort.
How much water should be used to fill the jetted tub for cleaning?
You should typically utilize two-thirds of the whole capacity of a rectangle jetted bathtub for cleaning. Use a cup filled with water to measure the appropriate quantity if your jetted tub is very huge or oddly shaped.
Because too little or too much water might impact the performance and pressure of the jets while they are in use, it is crucial to only utilize two-thirds of the entire capacity during a deep clean.
The motor that drives the jets may get overworked and may fail if there is too much water present. Also, heating up an excessive amount of water will consume more energy (typically electric), which results in higher monthly utility costs.
Thus, it may be costly in several different ways to overfill a jet tub.
How Often Should You Use Dishwasher Tablets to Clean the Jetted Tub?
The ideal approach, according to the common agreement, is to use dishwashing detergent tablets to clean your jetted tub at least twice a month. This makes sure that any accumulation of filth or scum is eliminated before it may build up and cause issues.
Dishwasher tablets work well for dissolving soap scum, calcium deposits, and other debris that can over time easily build up in your jetted tub’s piping system. Always keep in mind that you don’t need to use a lot of dishwashing tablets to get good results.
You can maintain the greatest appearance for your jetted tub with even little dosages. It’s also crucial to keep in mind that some of these cleaners include strong chemicals that, if used too frequently or without the right safety precautions, like as wearing gloves and eye protection when handling them, might harm the pipes.
Are Jetted Bathtubs Safe to Clean with Vinegar?
A jetted tub may be safely and effectively cleaned with vinegar. Its acidic nature effectively removes soap scum and hard water deposits while also eradicating germs, bacteria, and other viruses.
It’s crucial to dilute the vinegar with water before applying it to a jetted tub to clean it. Two parts water and one part white vinegar ought to be adequate. The jetted tub’s surfaces, including its walls and any exposed pipes or jets, should next be sprayed with the dilute solution.
Is there anything that can’t be used to clean a jetted tub?
Never use any chemical-based cleaning products, such as bubble baths, body oils, shampoos, soaps, or fabric softeners in jetted bathtubs. These compounds have the potential to produce foam that can jam jets and stick to pipelines.
Moreover, they could leave residues on the pipe walls that stop water flow and encourage bacterial development inside the tubing system. Several jetted tub models’ filters are affected by this foam as well.
Even granulated salt crystals may be a concern in a jetted tub because the sharp edges can wear out internal components like pumps and valves over time from abrasive particles continuously rubbing against them.
Is it Possible to Clean a Jetted Bathtub with Bleach?
Although chlorine bleach is a common home cleanser and disinfectant used for various cleaning activities, it is generally not advised to use chlorine bleach in jetted tubs for a number of reasons.
Bleach has the potential to harm various parts of jetted bathtubs, including circulating pumps, filters, and pipes. Because they are often made of plastic or PVC, pipes are particularly prone to damage.
Bleach has a far greater chlorine content than regular bathing water and tap water, which might also harm the tub. If the skin comes into touch with this high concentration, it might become damaged (if left after cleaning).
Use Dishwasher Tablets to Clean & Sparkle Your Jetted Tub
The answer is to use dishwashing tablets to clean a jetted tub. The procedure couldn’t be much easier as there’s no need for expensive specialized equipment or harsh chemicals. No laborious scrubbing is necessary; all you need is hot water and a dishwashing tablet. Next, just follow our simple instructions to obtain dazzling results.
Not only is it simple to do, there is no need for complicated machinery or toxic chemicals. So don’t put it off any longer and start enjoying hours of peaceful relaxation in your brand-new jetted tub.